Picture of Victron Energy ORI481260020 Orion 48/12-60A DC-DC Converter, 48 V to 12 V
Victron Energy ORI481260020 Orion 48/12-60A DC-DC Converter, 48 V to 12 V
  • $131.75
  • In Stock
  • SKU: ORI481260020

Victron Energy ORI481260020 Orion 48/12-60A DC-DC Converter, 48 V to 12 V

Runs 12 V lights, radios, pumps and audio from a 48 V battery bank in golf carts, solar and off-grid systems, boats and RVs. 60 A continuous (65 A maximum) from a 38 to 66 V DC input, with the output set anywhere from 10 to 15 V. Non-isolated, IP20 for dry, ventilated spaces. Read Full Description
$131.75
Availability: In Stock
SKU: ORI481260020
GTIN: 8719076075455

The Victron Orion 48/12-60A is a 48 V to 12 V DC-DC converter for running 12 V equipment from a 48 V battery bank. It delivers 60 A continuous at an output you set between 10 and 15 V, for the lights, radios, pumps and audio in a golf cart, solar system, boat or RV.

60 A Continuous output
38 to 66 V DC Input range
10 to 15 V Adjustable output
92 % Efficiency

Key specifications

Part numberORI481260020
Input voltage range38 to 66 V DC
Under-voltage shutdown / restart38 V / 40 V
Output voltage10 to 15 V, adjustable (factory setting 13.2 V)
Continuous / maximum output current60 A / 65 A
Efficiency92 %
Off-load currentLess than 20 mA
Galvanic isolationNo (non-isolated)
CoolingFan assisted, temperature controlled
Parallel operationUp to 5 units
Operating temperature-4 to 131 °F (-20 to 55 °C), derated above 104 °F (40 °C)
DC connectionsM6 bolts
Protection ratingIP20
Weight2.0 lb (0.9 kg)
Dimensions (H x W x D)2.6 x 3.5 x 7.7 in (65 x 88 x 195 mm)

Setting it up

Mount it in a cool, dry, ventilated spot: the case is IP20, so it belongs inside a cabinet or compartment, away from spray. Connect the negative cables first. Victron warns that a poor negative connection can push the output voltage too high.

The output leaves the factory at 13.2 V. To change it, turn the potentiometer with a small slotted screwdriver, clockwise to raise it, while a small load is connected.

For remote on/off, replace the wire bridge on the green connector with a small switch (under 100 mA), or feed its right-hand terminal from the 48 V supply through an ignition or run/stop switch. No heavy switch is needed in the 48 V cable.

Common questions

What circuit protection does it need?

A fuse or breaker on the 48 V input cable and another on the 12 V output cable, each sized for its wire. On the input side, use parts rated for 48 V DC.

Is it isolated?

No. The 48 V and 12 V sides share the negative, which suits a system wired on one common negative. A system that must keep the two sides apart needs an isolated converter.

Can it charge a 12 V battery?

Victron rates it to buffer-charge a battery: set the output to the battery's charge or float voltage. It holds that one voltage with no charge stages, so it keeps an accessory battery topped up rather than replacing a charger.

The datasheet, the instruction sheet and the dimension drawing are in the Downloads section of this page.

Customer Reviews

Write a review of this product and share your opinion with others.
Not Good Needs That Special Something Average, Ordinary That's Good Stuff Perfect. It doesn't get any better
The most useful comments contain specific examples about:
  • How you use the product
  • Things that are great about it
  • Things that aren't so great about it